ATA8743-PXQW【PDF 115/238 页】MCU W/TRANSMITTER ASK/FSK 24QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录52

111页 112页 113页 114页 [115页]116页 117页 118页 119页

115

9152BINDCO02/10

ATA8743

tion mode (WGM13:0) bits must be set before the TOP value can be written to the ICR1

before the low byte is written to ICR1L.

For more information on how to access the 16-bit registers refer to Accessing 16-bit Registers

on page 110.

21.6.1

Input Capture Trigger Source

The main trigger source for the Input Capture unit is the Input Capture pin (ICP1).

Timer/Counter1 can alternatively use the Analog Comparator output as trigger source for the

Input Capture unit. The Analog Comparator is selected as trigger source by setting the Analog

Comparator Input Capture (ACIC) bit in the Analog Comparator Control and Status Register

(ACSR). Be aware that changing trigger source can trigger a capture. The Input Capture Flag

must therefore be cleared after the change.

Both the Input Capture pin (ICP1) and the Analog Comparator output (ACO) inputs are sampled

using the same technique as for the T1 pin (Figure 22-1 on page 136). The edge detector is also

identical. However, when the noise canceler is enabled, additional logic is inserted before the

edge detector, which increases the delay by four system clock cycles. Note that the input of the

noise canceler and edge detector is always enabled unless the Timer/Counter is set in a Wave-

form Generation mode that uses ICR1 to define TOP.

An Input Capture can be triggered by software by controlling the port of the ICP1 pin.

21.6.2

Noise Canceler

The noise canceler improves noise immunity by using a simple digital filtering scheme. The

noise canceler input is monitored over four samples, and all four must be equal for changing the

output that in turn is used by the edge detector.

The noise canceler is enabled by setting the Input Capture Noise Canceler (ICNC1) bit in

Timer/Counter Control Register B (TCCR1B). When enabled the noise canceler introduces addi-

tional four system clock cycles of delay from a change applied to the input, to the update of the

ICR1 Register. The noise canceler uses the system clock and is therefore not affected by the

prescaler.

21.6.3

Using the Input Capture Unit

The main challenge when using the Input Capture unit is to assign enough processor capacity

for handling the incoming events. The time between two events is critical. If the processor has

not read the captured value in the ICR1 Register before the next event occurs, the ICR1 will be

overwritten with a new value. In this case the result of the capture will be incorrect.

When using the Input Capture interrupt, the ICR1 Register should be read as early in the inter-

rupt handler routine as possible. Even though the Input Capture interrupt has relatively high

priority, the maximum interrupt response time is dependent on the maximum number of clock

cycles it takes to handle any of the other interrupt requests.

Using the Input Capture unit in any mode of operation when the TOP value (resolution) is

actively changed during operation, is not recommended.

Measurement of an external signals duty cycle requires that the trigger edge is changed after

each capture. Changing the edge sensing must be done as early as possible after the ICR1

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式